Wrong codes displayed

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jm43130
    Senior Member
    • Apr 2008
    • 182

    Wrong codes displayed

    Recently had a 2018 GMC Terrain in Vin 3GKALPEV9JL255716 in with ABS,Trac, Stability, Check engine lights on, Dud a full system scan, Had various system U codes, mostly U0073 can"A" code, rt rr wheel speed sensor missing code C0050, C025F master cylinder calibration not learned, U0422 missing parking assist data, and all other various U codes for missing communication with various modules. Scanned wss and was missing rear speed signal, was able to swap side to side, still right side dead. Next step was look at EBCM, but had a new one installed with correct calibration. Decided to try GDS 2 and it had all different codes, mainly U0077, which is HS Can 2 off line. This is different circuits than Can A which is terminal 6 and 14 in DLC. This is terminals 12 and 13 in DLC.Ended up be bad x402 connector in rt rr of vehicle, had pins for Can 2 pushed out. Repaired wiring, cleared codes, rechecked. Still had code C0025f in ABS. There was a setup procedure in SPS to do this. Performed EBCM setup procedure, rear brake caliper calibration , all okay now. Verus showed U0073 for Can A problem. GDS 2 had code U0077, CAN 2 problem. completely different diagnostic tree. Probably didn't need EBCM replaced at all.
  • Rich Shepherd
    Snap-on D&I
    • Nov 2006
    • 553

    #2
    Can you provide the code scan you did on the vehicle?
    Thanks,

    Comment

    • jm43130
      Senior Member
      • Apr 2008
      • 182

      #3
      Rich, I've tried. I can't figure out how to attach files to these posts. I've got them on my PC. How do I attach a file to these posts?

      Comment

      • Steve6911
        Moderator
        • Feb 2007
        • 2168

        #4
        John

        Scroll down to "Manage attachments"

        Capture2.JPG

        A new menu will open up asking you to select the files, select them the click upload, then close that menu.Click on the Paperclip and it will allow you to attach your uploaded files to the post.

        Capture.JPG

        Comment

        • jm43130
          Senior Member
          • Apr 2008
          • 182

          #5
          https://productforum.autorepairdata....1&d=1616075000
          Attached Files

          Comment

          • jm43130
            Senior Member
            • Apr 2008
            • 182

            #6
            CCF_000009.pdf

            There were more codes on GDS but these are ones I chose.

            Comment

            • Rich Shepherd
              Snap-on D&I
              • Nov 2006
              • 553

              #7
              What version of software do you have on your Verus Pro?

              Thanks Steve for helping with the attachments.

              Comment

              • jm43130
                Senior Member
                • Apr 2008
                • 182

                #8
                It's a Verus Edge and I have 20.4 on it.

                Comment

                • ToltecasChavez
                  Senior Member
                  • Apr 2011
                  • 408

                  #9
                  When is the new Software Update Coming out? Thanks

                  Comment

                  • Rich Shepherd
                    Snap-on D&I
                    • Nov 2006
                    • 553

                    #10
                    Originally posted by ToltecasChavez
                    When is the new Software Update Coming out? Thanks
                    The software release this time of year is typically around the first week of April. Check with your dealer for more specific availability info.

                    Comment

                    • ToltecasChavez
                      Senior Member
                      • Apr 2011
                      • 408

                      #11
                      Originally posted by Rich Shepherd
                      The software release this time of year is typically around the first week of April. Check with your dealer for more specific availability info.
                      Thank you. I'm going to trade my Solus Edge For the D10. Which I'm already paying for. But I'm trading it with the latest version. Thanks!

                      Comment

                      • Steve6911
                        Moderator
                        • Feb 2007
                        • 2168

                        #12
                        I think your really gonna like the D10 Jorge! It's an awesome machine.

                        Comment

                        • jm43130
                          Senior Member
                          • Apr 2008
                          • 182

                          #13
                          Seems like no one else is looking at my original post.
                          What about Verus Edge on 20.4 not displaying codes correctly?

                          Comment

                          • Steve6911
                            Moderator
                            • Feb 2007
                            • 2168

                            #14
                            John

                            Rich took your information, things take time. This will not be a two second fix. It will be looked at and hopefully corrected as soon as possible.

                            Steve

                            Comment

                            • ToltecasChavez
                              Senior Member
                              • Apr 2011
                              • 408

                              #15
                              Thank you steve! I tried it out and the thing boots in 2 seconds! None of the other tools right now boot that fast. Can't wait. My distributor just told me the latest version is out. But I see no updates on ShopStream Connect.

                              Comment

                              Working...